The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting showsand R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026：：1：1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026：：1：2/122
ipv6 ospf 6 area 0
Figure 3
What is the solution of the fault condition？（）
A.Add ipv6 ospf 6 area 0 under S0/0/0/0.23 on R2
B.Add ipv6 ospf 6 area 6 under s0/0/0/0.23 on R2
C.Remove IPv6 address from s0/0/0/0.23 on R2
D.Enable IPv6 routing on s0/0/0/0.23 on R2
您可能感興趣的試卷
你可能感興趣的試題
The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting shows and R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026：：1：1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026：：1：2/122
ipv6 ospf 6 area 0
Figure 3
The Fault Condition is related to which technology？（）
A.IPv6 Addressing
B.Route Redistribution
C.OSPFv3
D.RIPng
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the Fa0/1interface of R4 but not the s0/0/0/0.34 interface.
Configurationon DSW1
router eigrp 10
network 10.1.4.4 0.0.0.0
network 10.2.1.1 0.0.0.0
network 10.2.4.13 0.0.0.0
no auto-summary
Configurationon DSW2
router eigrp 10
network 10.1.4.8 0.0.0.0
network 10.2.2.1 0.0.0.0
network 10.2.4.14 0.0.0.0
no auto-summary
Configurationon R4
router eigrp 10
network 10.1.4.5 0.0.0.0
no auto-summary
redistribute ospf 1 metric 100 10 255 1 1500 route-map EIGRP_to_OSPF !
router ospf 1
network 10.1.1.8 0.0.0.0 area 34
redistribute eigrp 10 subnets!
route-map EIGRP→OSPF
match ip address 1!
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 209.0.0.0 0.255.255.255
What is the solution of the fault condition？（）
A.Remove the redistribute command from OSPF process on R4
B.Change the route-map name in the redistribute command under OSPF process to EIGRP→OSPF on R4
C.Change EIGRP AS to 1 on R4
D.Advertise 10.1.1.8/30 network in EIGRP on R4
最新試題
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Network Topology Exhibit：Configuration Exhibit：NET（config）# access-list 112 deny icmp any any echo logNET（config）# access-list 112 deny imp any any redirect logNET（config）# access-list 112 deny icmp any any mask-request logNET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET（config）# interface Fa0/1NET（config-if）# ip access-group 112 inYou work as a network administrator at networkTut.com， study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.