A.All traffic is tagged with a specific VLAN ID from the VLAN of the attacker and is now viewable
B.Clients will forward packets to the attacking device， which will in turn send them to the desireddestination but not before recording the traffic patterns
C.All traffic is redirected to the VLAN that the attacker used to flood the CAM table
D.All traffic is flooded out all ports and an attacker is able to capture all data
E.None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
A.MAC spoofing
B.VLAN hopping
C.MAC address flooding
D.DHCP flooding
E.Session hijacking
A.Enable BPD guard
B.Disable CDP on ports where it is not necessary
C.Place unused ports in a common unrouted VLAN
D.Prevent automatic trunk configuration
E.Implement port security
Refer to the exhibit. Based upon the configuration， you need to understand why the policy routingmatch counts are not increasing. Which would be the first logical step to take？Select the bestresponse.（）
A.Confirm if there are other problematic route-map statements thatprecede divert
B.Check the access list for log hits
C.Check the routing table for 212.50.185.126
D.Remove any two of the set clauses（Multiple set clause entries will cause PBR to use therouting table.）
Study the following graphic carefully Host1 and Host2， which belong to different VLANs， are in thesame subnet. According to the information displayed， which description is correct when trying toping from host to host？（）
A.A trunk port should be configured on the link between CK-SW1 and CK-SW2 to pingsuccessfully
B.The two hosts should be in the same VLAN in order to ping successfully
C.A Layer 3 device is a must in order for the ping command to be successful
D.The ping command will be successful without any further configuration changes
Refer to the exhibit. VLAN2， VLAN3， and VLAN10 are configured on the switch D-SW1.Host computers are on VLAN 2 （10.1.2.0）， servers are on VLAN 3 （10.1.3.0）， and the
management VLAN is on VLAN10 （10.1.10.0）. Hosts are able to ping each other but are unable toreach the servers. On the basis of the exhibited output， which configuration solution could rectifythe problem？（）
A.Enable IP routing on the switch D-SW1
B.Configure a default route that points toward network 200.1.1.0/24
C.Assign an IP address of 10.1.3.1/24 to VLAN3
D.Configure default gateways to IP address 10.1.2.1 on each host
E.Configure default gateways to IP address 10.1.10.1 on each host
F.Configure default gateways to IP address 200.1.1.2 on each host
最新試題
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
cisco ios command to interface dialer 0
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Study the exhibit carefully.Routers A and B are customer routers. Routers 1， 2， 3 and 4 are provider routers. The routers areoperating with various IOS versions. Which frame mode MPLS configuration statement is true？（）
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
Which statement about PPPoA configuration is correct？（）