Refer to the exhibit.
Which interface or interfaces on switch SW_A can have the port security feature enabled？（）
A. Ports 0/1 and 0/2
B. The trunk port 0/22 and the EtherChannel ports
C. Ports 0/1， 0/2 and 0/3
D. Ports 0/1， 0/2， 0/3， the trunk port 0/22 and the EtherChannel ports
E. Port 0/1
F. Ports 0/1， 0/2， 0/3 and the trunk port 0/22
您可能感興趣的試卷
你可能感興趣的試題
A Company switch was configured as shown below：
switchport mode access switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
Given the configuration output shown above，
what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.
E. None of the other alternatives apply
VLAN maps have been configured on switch R1.
Which of the following actions are taken in a VLAN map that does not contain a match clause？ （）
A. Implicit deny feature at end of list.
B. Implicit deny feature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.
Refer to the exhibit. The web servers WS_1 and WS_2 need to be accessed by external and internal users. For security reasons， the servers should not communicate with each other，
although they are located on the same subnet. The servers do need， however， to communicate with a database server located in the inside network.
What configuration will isolate the servers from each other？ （）
A. The switch ports 3/1 and 3/2 will be defined as secondary VLAN community ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
B. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
C. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN community ports.
D. The switch ports 3/1 and 3/2 will be defined as secondary VLAN isolated ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
pany is implementing 802.1X in order to increase network security. In the use of 802.1X
access control，
which three protocols are allowed through the switch port before authentication takes place？ （）
A. EAP-over-LAN
B. EAP MD5
C. STP
D. protocols not filtered by an ACL
E. CDP
F. TACACS+
Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5？（）
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
最新試題
Which statement is correct about RSTP port roles？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
What two things will occur when an edge port receives a BPDU？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Which statement is true about the output？（）