Refer to the exhibit. Port security has been configured on the switch port Fa0/5.
What would happen if another device is connected to the port after the maximum number of devices has been reached， even if one or more of the original MAC addresses are inactive？（）
A. The port will permit the new MAC address because one or more of the original MAC addresses are inactive.
B. The port will permit the new MAC address because one or more of the original MAC addresses will age out.
C. Because the new MAC address is not configured on the port， the port will not permit the new MAC address.
D. Although one or more of the original MAC addresses are inactive， the port will not permit the new MAC address.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
What is the problem with this configuration？（）
A. Spanning tree PortFast cannot be configured on a port where a voice VLAN is configured.
B. Sticky secure MAC addresses cannot be used on a port when a voice VLAN is configured.
C. Spanning tree PortFast cannot be configured on a port when a sticky secure MAC address is used.
D. The switch port must be configured as a trunk.
You need to configure port security on switch R1.
Which two statements are true about this technology？ （）
A. Port security can be configured for ports supporting VoIP.
B. With port security configured， four MAC addresses are allowed by default.
C. The network administrator must manually enter the MAC address for each device in order for the switch to allow connectivity.
D. Withsecurity configured， only one MAC addresses is allowed by default.
E. Port security cannot be configured for ports supporting VoIP.
Refer to the exhibit. Based on the running configuration that is shown for interface FastEthernet0/2，
what two conclusions can be deduced？（）
A. Connecting a host with MAC address 0000.0000.4147 will move interface FastEthernet0/2 into error disabled state.
B. The host with address 0000.0000.4141 is removed from the secure address list after 5 seconds of inactivity.
C. The sticky secure MAC addresses are treated as static secure MAC addresses after the running configuration is saved to the startup configuration and the switch is restarted.
D. Interface FastEthernet0/2 is a voice VLAN port.
E. The host with address 0000.0000.000b is removed from the secure address list after 300 seconds.
Refer to the exhibit.
Which interface or interfaces on switch SW_A can have the port security feature enabled？（）
A. Ports 0/1 and 0/2
B. The trunk port 0/22 and the EtherChannel ports
C. Ports 0/1， 0/2 and 0/3
D. Ports 0/1， 0/2， 0/3， the trunk port 0/22 and the EtherChannel ports
E. Port 0/1
F. Ports 0/1， 0/2， 0/3 and the trunk port 0/22
A Company switch was configured as shown below：
switchport mode access switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
Given the configuration output shown above，
what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.
E. None of the other alternatives apply
最新試題
Which three statements about STP timers are true？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Which two statements are true when the extended system ID feature is enabled？ （）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）