A. The IP addresses of workstations allowed gain access to the router via an access list
B. Permanent name-to-address mappings created using the ip host command.
C. Temporary and permanent DNS entries.
D. The names of the routers created using the hostname command.
E. The length of time of users logged into the router, as well as the duration
您可能感興趣的試卷
你可能感興趣的試題
A. application layer
B. session layer
C. transport layer
D. internet layer
E. network layer
F. data link layer
G. physical layer
A. The Popcorn router is not forwarding RIP updates.
B. The Popcorn router did not include network 192.168.12.0 in its routing configuration.
C. The Ethernet1 interface of the Popcorn router is shutdown.
D. The clockrate is not present in the configuration of one of the routers.
E. The Serial interface of the Popcorn router is not operating.
A. TK1#show ip eigrp adjacency
B. TK1#show ip eigrp topology
C. TK1#show ip eigrp interfaces
D. TK1#show ip eigrp neighbors
E. None of the above
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:
TK1(config)# router ospf 1
TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0
After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）
A. The AS is not correctly configured
B. The network subnet mask is incorrectly configured
C. The network wildcard mask is configured incorrectly
D. The network number is not correctly configured
E. The process id is configured incorrectly
F. None of the above
On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?（）
A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.
最新試題
How many usable sub network and usable hosts per subnet result in the network address 201.105.13.0 is sub netted with a mask of /26? （）
Which of the following correctly describe steps in the OSI data encapsulation process?（）
Which command is used to display the placement and direction of an IP access control list on a router?（）
What is the subnetwork address for a host with IP address 201.100.5.68/28?（）
Identify three valid host addresses in the 192.168.27.0 network with a subnet mask of 255.255.255.240. （）
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）
What does a configuration Register Setting of 0x2105 indicate to the Router? （）