Refer to the exhibit.
Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
A. Router A is the master virtual router， and Router B is the backup virtual router. When Router A fails， Router B will become the master virtual router. When Router A recovers， Router B will maintain the role of master virtual router.
B. Router B is the master virtual router， and Router A is the backup virtual router. When Router B fails， Router A will become the master virtual router. When Router B recovers， it will regain the master virtual router role.
C. Router A is the master virtual router， and Router B is the backup virtual router. When Router A fails， Router B will become the master virtual router. When Router A recovers， it will regain the master virtual router role.
D. Router B is the master virtual router， and Router A is the backup virtual router. When Router B fails， Router A will become the master virtual router. When Router B recovers， Router A will maintain the role of master virtual router.
您可能感興趣的試卷
你可能感興趣的試題
Exhibit：
Exhibit：
You work as a network engineer at Company. You study the exhibit carefully. Which GLBP device hosts receive the MAC address assignment？（）
A. R1
B. R2
C. The AVG
D. The AVF
E. None of the other alternatives apply
On a 3550 EMI switch，
which three types of interfaces can be used to configure HSRP？ （）
A. Loopback interface
B. SVI interfac
C. Routed port
D. Access port
E. EtherChannel port channel
F. BVI interface
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？ （）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails.
What command would you use if you wanted to configure this？ （）
A. en standby preempt
B. standby preempt enable
C. standby preempt
D. hot standby preempt
A. Define the encapsulation type.
B. Define the standby router.
C. Define the standby IP address.
D. Enable the standby priority.
最新試題
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Which two statements about the various implementations of STP are true？（）