A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1.
Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）
A. The next hop is I2's BGP RID
B. The next hop is I2's IP address used on the R2 - I2 neigh bor relationship
C. The next hop is R2's BGP RID
D. The next hop is R2's IP address used on the R1 - R2 neighbor relationship
您可能感興趣的試卷
你可能感興趣的試題
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）
R1# show ip bgp 190.1.0.0/16
BGP routing table entry for 190.1.0.0/16, version 121
Paths: (1 available, best #1, table Default - IP - Routing - Table)
Advertised to update - groups:
1
1 2 3 4
1.1.1.1 from 2.2.2.2 (3.3.3.3)
Origin IGP, metric 0, localpref 100, valid, internal, best
A. R1 has a neighbor 1.1.1.1 command configured.
B. R1 has a neighbor 2.2.2.2 command configured.
C. The show ip bgp command lists a line for 190.1.0.0/16 with both a n > and an i on the left.
D. R1 is in ASN 1.
R1 in ASN 1 with loopback1 address 1.1.1.1 needs to be configured with an iBGP connection to R2 with loopback2 IP address 2.2.2.2. The connection should use the loopbacks.
Which o f the following commands is required on R1?（）
A. neighbor 1.1.1.1 remote- as 1
B. neighbor 2.2.2.2 remote- as 2
C. neighbor 2.2.2.2 update - source loopback1
D. neighbor 2.2.2.2 ibgp -multihop 2
E. neighbor 2.2.2.2 ibgp - mode
Router R1 has eBGP connections to I1 and I 2, routers at the same ISP. The company that owns R1 can use public address range 130.1.16.0/20. The following output lists all the IP routes in R1's routing table within this rangE. Which of the following answers would cause R1 to advertise the 130.1.1 6.0/20 prefix to its eBGP peers?（）
R1# show ip route 130.1.16.0 255.255.240.0 longer - prefixes
! lines omitteD...
O 130.1.16.0/24 [110/3] via 10.5.1.1, 00:14:36, FastE thernet0/1
O 130.1.17.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1
O 130.1.18.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1
A. Configure R1 with the network 130.1.16.0 mask 255.255.240.0 command.
B. Configure R1 with the network 130.1.16 .0 mask 255.255.240.0 summaryonly command.
C. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed.
D. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed, and create a BGP summary for 130.1.16.0/20.
The fol lowing line of output was extracted from the output of the show ip bgp command on Router R1. Which of the following can be determined from this output?（）
Network Next Hop Metric LocPrf Weight Path
* 130.1.1.0/28 1.1.1.1 0 1 2 3 4 i
A. The route is learne d from an eBGP peer
B. The route has no more than three ASNs in the AS_PatH
C. The route is the best route for this prefix
D. None of these facts can be positively determined by this output
最新試題
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable