Refer to the show interface Gi0/1 switchport command output shown in the exhibit.
Which two statements are true about this interface？（）
A. This interface is a member of a voice VLAN.
B. This interface is configured for access mode.
C. This interface is a dot1q trunk passing all configured VLANs.
D. This interface is a member of VLAN7.
E. This interface is a member of VLAN1.
您可能感興趣的試卷
你可能感興趣的試題
You’re a network administer and you issue the command （show port 3/1） on an Ethernet port. To your surprise you notice a non-zero entry in the ’Giants’ column.
What could be the cause of this？ （）
A. IEEE 802.1Q
B. IEEE 802.10
C. Misconfigured NIC
D. User configuration
E. All of the above
The Company administrator has issue the "show vlan id 5" command.
What will this command display？ （）
A. Ports in VLAN 5
B. Utilization
C. VLAN information on port 0/5
D. Filters
E. MTU and type
Which of the following should you enable to prevent a switch from forwarding packets with source addresses that are outside an administratively defined group？ （）
A. DAI
B. STP
C. PVLAN
D. port security
Refer to the exhibit. The switchport output in Figure 1 displays the default settings of interface FastEthernet 0/13 on switch SW1. Figure 2 displays the desired interface settings.
Which command sequence would configure interface FastEthernet 0/13 as displayed in Figure 2？ （）
A. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode trunk SW1（config-if）# switchport trunk native DATA SW1（config-if）# switchport trunk allowed vlan 1，10，20
B. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic auto SW1（config-if）# switchport trunk native DATA SW1（config-if）# witchport trunk allowed vlan add 1，10，20
C. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic desirable SW1（config-if）# switchport trunk native vlan DATA SW1（config-if）# switchport trunk allowed vlan 1，10，20
D. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic desirable SW1（config-if）# switchport trunk native vlan 10 SW1（config-if）# switchport trunk allowed vlan 1，10，20
E. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic Desirable SW1（config-if）# switchport trunk native vlan 10
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch，
which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）
A. switchport access vlan vlan-id
B. switchport
C. switchport mode access
D. no switchport
E. None of the other alternatives apply
最新試題
Which two statements about the various implementations of STP are true？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）