A. Used to relay DHCP messages
B. Used to communicate with LAPs
C. Used to bring up LWAPP tunnels
D. Used to extend into the wireless client VLAN
您可能感興趣的試卷
你可能感興趣的試題
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group.
What can be done to make the group function properly ？ （）
A. On DS1， disable preempt
B. On DS2， decrease the priority value to a value less than 150
C. On DS1， increase the decrement value in the track command to a value greater than 6
D. On DS1， disable track command.
A. 50
B. 100
C. 150
D. 200
If G1/0/1 on DS1 is shutdown，
what will be the current priority value of the Vlan105’s group on DS1 ？（）
A. 95
B. 100
C. 150
D. 200
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group.
What can be done to make the group function properly ？ （）
A. On DS1， disable preempt
B. On DS1， decrease the priority value to a value less than 190 and greater than 150
C. On DS2， increase the priority value to a value greater 241 and less than 249
D. On DS2， increase the decrement value in the track command to a value greater than 10 and less than 50.
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired.
What need to be done to make the group for Vlan101 function properly ？ （）
A. Enable preempt on DS1’s Vlan101 HSRP group
B. Disable preempt on DS1’s Vlan101 HSRP group
C. Decrease DS1’s priority value for Vlan101 HSRP group to a value that is less than priority value configured on DS2’s HSRP group for Vlan101
D. Decrease the decrement in the track command for DS1’s Vlan 101 HSRP group to a value less than the value in the track command for DS2’s Vlan 101 HSRP group.
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）