Refer to the exhibit. Based upon the output of show vlan on switch CAT2，
what can we conclude about interfaces Fa0/13 and Fa0/14？ （）
A. that interfaces Fa0/13 and Fa0/14 are in VLAN 1
B. that interfaces Fa0/13 and Fa0/14 are down
C. that interfaces Fa0/13 and Fa0/14 are trunk interfaces
D. that interfaces Fa0/13 and Fa0/14have a domain mismatch with another switch
E. that interfaces Fa0/13 and Fa0/14have a duplex mismatch with another switch
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Switch P1S1 is not applying VLAN updates from switch P2S1.
What are three reasons why this is not occurring？（）
A. Switch P2S1 is in server mode.
B. Switch P1S1 is in transparent mode.
C. The MD5 digests do not match.
D. The passwords do not match.
E. The VTP domains are different.
F. VTP trap generation is disabled on both switches.
Refer to the show interface Gi0/1 switchport command output shown in the exhibit.
Which two statements are true about this interface？（）
A. This interface is a member of a voice VLAN.
B. This interface is configured for access mode.
C. This interface is a dot1q trunk passing all configured VLANs.
D. This interface is a member of VLAN7.
E. This interface is a member of VLAN1.
You’re a network administer and you issue the command （show port 3/1） on an Ethernet port. To your surprise you notice a non-zero entry in the ’Giants’ column.
What could be the cause of this？ （）
A. IEEE 802.1Q
B. IEEE 802.10
C. Misconfigured NIC
D. User configuration
E. All of the above
The Company administrator has issue the "show vlan id 5" command.
What will this command display？ （）
A. Ports in VLAN 5
B. Utilization
C. VLAN information on port 0/5
D. Filters
E. MTU and type
Which of the following should you enable to prevent a switch from forwarding packets with source addresses that are outside an administratively defined group？ （）
A. DAI
B. STP
C. PVLAN
D. port security
最新試題
Which statement is correct about RSTP port roles？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Which three statements about STP timers are true？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）