Refer to the exhibit. Based on the running configuration that is shown for interface FastEthernet0/2，
what two conclusions can be deduced？（）
A. Connecting a host with MAC address 0000.0000.4147 will move interface FastEthernet0/2 into error disabled state.
B. The host with address 0000.0000.4141 is removed from the secure address list after 5 seconds of inactivity.
C. The sticky secure MAC addresses are treated as static secure MAC addresses after the running configuration is saved to the startup configuration and the switch is restarted.
D. Interface FastEthernet0/2 is a voice VLAN port.
E. The host with address 0000.0000.000b is removed from the secure address list after 300 seconds.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.
Which interface or interfaces on switch SW_A can have the port security feature enabled？（）
A. Ports 0/1 and 0/2
B. The trunk port 0/22 and the EtherChannel ports
C. Ports 0/1， 0/2 and 0/3
D. Ports 0/1， 0/2， 0/3， the trunk port 0/22 and the EtherChannel ports
E. Port 0/1
F. Ports 0/1， 0/2， 0/3 and the trunk port 0/22
A Company switch was configured as shown below：
switchport mode access switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
Given the configuration output shown above，
what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.
E. None of the other alternatives apply
VLAN maps have been configured on switch R1.
Which of the following actions are taken in a VLAN map that does not contain a match clause？ （）
A. Implicit deny feature at end of list.
B. Implicit deny feature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.
Refer to the exhibit. The web servers WS_1 and WS_2 need to be accessed by external and internal users. For security reasons， the servers should not communicate with each other，
although they are located on the same subnet. The servers do need， however， to communicate with a database server located in the inside network.
What configuration will isolate the servers from each other？ （）
A. The switch ports 3/1 and 3/2 will be defined as secondary VLAN community ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
B. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
C. The switch ports 3/1 and 3/2 and the ports connecting to the two firewalls will be defined as primary VLAN community ports.
D. The switch ports 3/1 and 3/2 will be defined as secondary VLAN isolated ports. The ports connecting to the two firewalls will be defined as primary VLAN promiscuous ports.
pany is implementing 802.1X in order to increase network security. In the use of 802.1X
access control，
which three protocols are allowed through the switch port before authentication takes place？ （）
A. EAP-over-LAN
B. EAP MD5
C. STP
D. protocols not filtered by an ACL
E. CDP
F. TACACS+
最新試題
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
What two things will occur when an edge port receives a BPDU？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）